CentOS Linux 7 [TuxCare] 安全性更新：bpftool / kernel / kernel-debug / kernel-debug-devel / kernel-devel / etc 多個弱點 （CENTOS7：CLSA-2024：1727167500）
high Nessus Plugin ID 360233
語言:
概要
CentOS Linux 主機缺少一個或多個安全性更新。說明
CentOS Linux 7 主機已安裝的套件會受到 TuxCare CENTOS7：CLSA-2024：1727167500 公告中提及的多個弱點影響。- 在 6.6.8 及更低版本的 Linux 核心中，net/bluetooth/af_bluetooth.c 中的 bt_sock_recvmsg 存在釋放後使用情形，這是因為 bt_sock_ioctl 爭用情形所致。(CVE-2023-51779)
- 已解決 Linux 核心中的下列弱點：netfilter: nftables: exthdr: fix 4-byte stack OOB write If priv->len is a multiple of 4, then dst[len / 4] can write past the destination array which leads to stack corruption. This construct is necessary to clean the remainder of the register in case ->len is NOT a multiple of the register size, so make it conditional just like nft_payload.c does.
The bug was added in 4.1 cycle and then copied/inherited when tcp/sctp and ip option support was added.
Bug reported by Zero Day Initiative project (ZDI-CAN-21950, ZDI-CAN-21951, ZDI-CAN-21961).
(CVE-2023-52628)
- 已解決 Linux 核心中的下列弱點：bnx2x: Fix multiple UBSAN array-index-out-of-bounds Fix UBSAN warnings that occur when using a system with 32 physical cpu cores or more, or when the user defines a number of Ethernet queues greater than or equal to FP_SB_MAX_E1x using the num_queues module parameter. Currently there is a read/write out of bounds that occurs on the array struct stats_query_entry query present inside the bnx2x_fw_stats_req struct in drivers/net/ethernet/broadcom/bnx2x/bnx2x.h. Looking at the definition of the struct stats_query_entry query array: struct stats_query_entry query[FP_SB_MAX_E1x+ BNX2X_FIRST_QUEUE_QUERY_IDX]; FP_SB_MAX_E1x is defined as the maximum number of fast path interrupts and has a value of 16, while BNX2X_FIRST_QUEUE_QUERY_IDX has a value of 3 meaning the array has a total size of 19. Since accesses to struct stats_query_entry query are offset-ted by BNX2X_FIRST_QUEUE_QUERY_IDX, that means that the total number of Ethernet queues should not exceed FP_SB_MAX_E1x (16). However one of these queues is reserved for FCOE and thus the number of Ethernet queues should be set to [FP_SB_MAX_E1x -1] (15) if FCOE is enabled or [FP_SB_MAX_E1x] (16) if it is not. This is also described in a comment in the source code in drivers/net/ethernet/broadcom/bnx2x/bnx2x.h just above the Macro definition of FP_SB_MAX_E1x. Below is the part of this explanation that it important for this patch /* * The total number of L2 queues, MSIX vectors and HW contexts (CIDs) is * control by the number of fast-path status blocks supported by the * device (HW/FW). Each fast-path status block (FP-SB) aka non-default * status block represents an independent interrupts context that can * serve a regular L2 networking queue. However special L2 queues such * as the FCoE queue do not require a FP-SB and other components like * the CNIC may consume FP-SB reducing the number of possible L2 queues * * If the maximum number of FP-SB available is X then: * a. If CNIC is supported it consumes 1 FP-SB thus the max number of * regular L2 queues is Y=X-1 * b. In MF mode the actual number of L2 queues is Y= (X-1/MF_factor) * c. If the FCoE L2 queue is supported the actual number of L2 queues * is Y+1 * d. The number of irqs (MSIX vectors) is either Y+1 (one extra for * slow-path interrupts) or Y+2 if CNIC is supported (one additional * FP interrupt context for the CNIC). * e. The number of HW context (CID count) is always X or X+1 if FCoE * L2 queue is supported. The cid for the FCoE L2 queue is always X. */ However this driver also supports NICs that use the E2 controller which can handle more queues due to having more FP-SB represented by FP_SB_MAX_E2. Looking at the commits when the E2 support was added, it was originally using the E1x parameters: commit f2e0899f0f27 (bnx2x: Add 57712 support). Back then FP_SB_MAX_E2 was set to 16 the same as E1x. However the driver was later updated to take full advantage of the E2 instead of having it be limited to the capabilities of the E1x. But as far as we can tell, the array stats_query_entry query was still limited to using the FP-SB available to the E1x cards as part of an oversignt when the driver was updated to take full advantage of the E2, and now with the driver being aware of the greater queue size supported by E2 NICs, it causes the UBSAN warnings seen in the stack traces below. This patch increases the size of the stats_query_entry query array by replacing FP_SB_MAX_E1x with FP_SB_MAX_E2 to be large enough to handle both types of NICs. Stack traces:
UBSAN: array-index-out-of-bounds in drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1529:11 index 20 is out of range for type 'stats_query_entry [19]' CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic #202405052133 Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 ---truncated--- (CVE-2024-42148)
- 已解決 Linux 核心中的下列弱點：mISDN: Fix a use after free in hfcmulti_tx() Don't dereference *sp after calling dev_kfree_skb(*sp). (CVE-2024-42280)
- 已解決 Linux 核心中的下列弱點：dev/parport: fix the array out-of-bounds risk Fixed array out-of-bounds issues caused by sprintf by replacing it with snprintf for safer data copying, ensuring the destination buffer is not overflowed. Below is the stack trace I encountered during the actual issue: [ 66.575408s] [pid:5118,cpu4,QThread,4]Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: do_hardware_base_addr+0xcc/0xd0 [parport] [ 66.575408s] [pid:5118,cpu4,QThread,5]CPU: 4 PID: 5118 Comm: QThread Tainted: G S W O 5.10.97-arm64-desktop #7100.57021.2 [ 66.575439s] [pid:5118,cpu4,QThread,6]TGID: 5087 Comm: EFileApp [ 66.575439s] [pid:5118,cpu4,QThread,7]Hardware name: HUAWEI HUAWEI QingYun PGUX-W515x-B081/SP1PANGUXM, BIOS 1.00.07 04/29/2024 [ 66.575439s] [pid:5118,cpu4,QThread,8]Call trace: [ 66.575469s] [pid:5118,cpu4,QThread,9] dump_backtrace+0x0/0x1c0 [ 66.575469s] [pid:5118,cpu4,QThread,0] show_stack+0x14/0x20 [ 66.575469s] [pid:5118,cpu4,QThread,1] dump_stack+0xd4/0x10c [ 66.575500s] [pid:5118,cpu4,QThread,2] panic+0x1d8/0x3bc [ 66.575500s] [pid:5118,cpu4,QThread,3] __stack_chk_fail+0x2c/0x38 [ 66.575500s] [pid:5118,cpu4,QThread,4] do_hardware_base_addr+0xcc/0xd0 [parport] (CVE-2024-42301)
請注意，Nessus 並未測試這些問題，而是僅依據應用程式自我報告的版本號碼作出判斷。
解決方案
根據 TuxCare 公告 CENTOS7：CLSA-2024：1727167500 中的指引更新受影響的套件。另請參閱
Plugin 詳細資訊
嚴重性: High
ID: 360233
檔案名稱: tuxcare_centos_7_CLSA-2024-1727167500.nasl
版本: 1.1
類型: Local
代理程式: unix
已發布: 2026/10/1
已更新: 2026/10/1
支援的感應器: Nessus Agent, Continuous Assessment, Tenable Cloud Security, Tenable Self-Hosted Container Security, Nessus
風險資訊
VPR
風險因素: High
分數: 7.6
百分位數: 98.67
Vendor
Vendor Severity: Important
CVSS v2
風險因素: Medium
基本分數: 6.8
時間性分數: 5
媒介: CVSS2#AV:L/AC:L/Au:S/C:C/I:C/A:C
CVSS 評分資料來源: CVE-2024-46673
CVSS v3
風險因素: High
基本分數: 7.8
時間性分數: 6.8
媒介: CVSS:3.0/AV:L/AC:L/PR:L/UI:N/S:U/C:H/I:H/A:H
時間媒介: CVSS:3.0/E:U/RL:O/RC:C
弱點資訊
必要的 KB 項目: Host/local_checks_enabled, Host/CentOS/release, Host/CentOS/rpm-list, Host/OS/extended-third-party
可輕鬆利用: No known exploits are available
修補程式發佈日期: 2024/9/24
弱點發布日期: 2021/7/21
參考資訊
CVE: CVE-2023-51779, CVE-2023-52628, CVE-2024-41071, CVE-2024-42148, CVE-2024-42280, CVE-2024-42301, CVE-2024-43882, CVE-2024-43900, CVE-2024-44940, CVE-2024-44987, CVE-2024-46673
CLSA: 2024:1727167500